To drive a motor to a direction, say, clockwise, the pin Input 1 must be high while the pin Input 2 must be low. The Enable A pin must be high to turn on the motor. For example, if a motor is using channel A, its terminals must be connected to pins Out 1 and Out 2. This IC drives two motors through two channels, A and B. It comes in two IC packages: MultiWatt15 and PowerSO20. The L298N is an integrated circuit that follows the H-bridge concept. This is very significant especially when using an Arduino board where the 5V power source is simply not enough for two DC motors. Please contact to our support team at for any question related to shipping.The other benefit of using an H-bridge is that you can provide a separate power supply to the motors.
L298N MOTOR DRIVER BUY FREE
For all the orders above INR 599, we offer a free shipping. We ship to all over India with flat shipping rate of INR 45 for all the orders below INR 599. Please read the product specifications and datasheet before selecting and ordering a product. Moreover we don't accept the return, if the ordered product is not fit for any specific application. We don't accept the returns for the products damanged by improper use of the product.
If you receive a different product then the ordered one, please contact us within the 3 days of you receive the product, supported by the proper pictures and description. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost. Once our support team accept the return, we will provide a replacement or a complete refund including the return shipping cost. If you receive a product with a manufacturing defect, please notify us within the 3 days of you receive the product, supported by the proper pictures and description. Below are the conditions where we can accept a return request. The basic dimensions of the L298N Motor Driver module are shown below.ĭue to the type of products we sell, we accept limited returns.
Maximum power consumption: 20W (when the temperature T = 75℃). Enable signal input high voltage range: 2.3V ≤ Vin ≤ Vss (enable signal active). 
Enable signal input low voltage range: 0.3V ≤ Vin ≤ 1.5V (enable signal inactive). Control Signal input High voltage range: 2.3 ≤ Vin ≤ Vss. Control Signal input Low voltage range: 0.3V ≤ Vin ≤ 1.5V. Driver: L298N Dual H Bridge DC Motor Driver. The same logic applied for Input 3 and 4 with Motor B. If they are made Low and High, then the motor will rotate counterclockwise. For example, if Input 1 and Input 2 are made High and Low, respectively, then Motor A will rotate in clockwise. You can adjust the speed of the motors by removing the jumper and providing a variable voltage between 0V to 5V by using a PWM signal.įinally, the four input pins Input 1, 2, 3, and 4 are used to control the direction of the motor. By default, there will be jumper pins connected to both Enable A and B to make them high (5V), this way the motors will rotate at maximum speed. The pins Enable A and Enable B are used to set the speed of the motor. If the operating voltage of the motor is greater than 12V then the built-in regulator will not be able to handle it, so we have to disconnect the regulator by removing the 5V Select Jumper pin and provide a separate 5V power as an input voltage to the 5V screw terminal to power our L298N Driver IC. If the operating voltage of the motor is less than or equal to 12V than the built-in regulator will power the driver IC, and this regulated 5V can also be obtained as an output voltage from the 5V screw terminal which can be used to power your microcontrollers like Arduino. The L298 IC requires 5V to operate, this is why we have a built-in 5V Linear Regulator. The voltage required to power the motor is provided to the Motor Power and Ground screw terminal, the voltage range should be between 7V to 35V. The motors to be controlled (Motor A and B) are connected to screw terminals. The pinout diagram of the L298N Motor Driver Module is shown below. The voltage rating of these motors can be between 5V to 35V and the peak current value can be up to 2A. The L298N Motor Driver module is based on the L298 Dual Full-Bridge Driver IC and can control the speed and direction of two DC motors (Motor A and Motor B) simultaneously. While the L293D motor driver module can be used for basic low current application the L298N Motor driver module is a high current motor driver with some additional features that are commonly used with Arduino and Raspberry Pi for Robotics applications. This is why we commonly use Motor Driver modules like the L293D Motor Driver Module and the L298N Motor Driver Module. A microcontroller that normally operates on 5V or 3.3V cannot be directly used to control a DC motor operating on higher voltage and current rating.
0 kommentar(er)
